GALAN - electric caldrons and heating equipments, GALAN - for houses, apartments, offices and cottages
|
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
Latvia; Riga; SIA "ALOVS"; Codes str. 24, LV-1003; tel/fax (+371) 67610688, mobile: 26761172
e-mail: galan@alovs.lv |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
Models charts of connecting of electric caldrons ÃÀËÀÍ
|
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
Of principle chart of connecting electric caldron
"ÃÀËÀÍ" 1. Electro-caldron ÃÀËÀÍ 2. Three moves valve 3. Pump of circulation 4. Filter 5. Drain valve 6. Dilator tank 7. Automation 8. Air to withdrew |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
Chart of the parallel connecting electric caldron
"ÃÀËÀÍ" 1. Electro-caldron ÃÀËÀÍ 2. Three moves valve 3. Pump of circulation 4. Filter 5. Drain valve 6. Dilator tank 7. Automation 8. Air to withdrew 9. Other source of heat (gas, oily or caldron on a hard fuel) |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
Connecting chart electric caldron "ÃÀËÀÍ" to the chimney
1. Electro-caldron ÃÀËÀÍ 2. Three moves valve 3. Pump of circulation 4. Filter 5. Drain valve 6. Dilator tank 7. Automation 8. Air to withdrew |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
Connecting chart electric caldron "ÃÀËÀÍ|" to the
radiator + warming up of floor Attention!
The area of warm floor not must exceed 30% to all heated area. 1. Electro-caldron ÃÀËÀÍ
2. Ball's valve 3. Pump of circulation 4. Filter 5. Drain valve 6. Dilator tank 7. Automation 8. Air to withdrew 9. Other source of heat (gas, oily or caldron on a hard fuel) 10. Three moves valve 11. Contour of heating of floor 12. Automation of heating of floor |
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
Connecting chart electro- caldron "ÃÀËÀÍ" to heating of floor
1. Electro-caldron ÃÀËÀÍ 2. Ball's valve 3. Pump of circulation 4. Filter 5. Drain valve 6. Dilator tank 7. Automation 8. Air to withdrew 9. Other source of heat (gas, oily or caldron on a hard fuel) 10. Three moves valve 11. Contour of heating of floor 12. Automation of heating of floor 13. Room thermostat 14. Motor of contour 15. Baypas |
|||||||||||||||||||||||||||||||||
For the start of electrode caldron in the system working on the warm floor it is necessary to prepare water as follows:
- To start the system and measure a current at the temperature of backpipe with 40 C.
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
If at 40 degrees on a backpipe | current falls short of to the parameters indicated in a table, it is necessary to make the
followings actions: 1. A current is less than - it is necessary to add salt contains | solution stage-by-stage (it diminishes specific resistance to the liquid).
First stage - no more tea-spoon salt waters on one hundred litres. If in 4 hours a current was multiplied it is insignificantly necessary to repeat the first stage. 2. A current is anymore - add the distilled water (it multiplies specific resistance to the liquid). After preparation of water temperature on an exit from a caldron (sensor ¹2) to decrease to 40 degrees. |
|||||||||||||||||||||||||||||||||
Attention!
At the use of electrodes caldrons for heating of chaffs the expense of electric power is considerably multiplied. |
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||